There are 270 products.
Active filters
95mm Shock Spring for INFERNO MP10/MP10T/MP10e/MP9. It is necessary for Buggy to use together with IFW624 HD Rear Shock Stay.
Optional parts for INFERNO MP10. Rear Shock Stay for IS215 Shock set.
Changed the existing shock mounting hole position to upper side.
Allows a longer shock travel than standard, which improves the performance when landing of jumps and bumpy section.
Stunning red anodized aluminum link rods for better appearance. For 120mm wheelbase.
Spare parts for MP10
High strength and precision construction of molded rear hub delivers improved controllability and better handling char
Spare parts for MP10
At first glance the radio plate looks similar to the MP9 TKI4, but the MP10 design features a revised servo position and increased strength with 3.0mm thickness, increased from 2.5mm.
2.2 inch rear wheel with offset suitable for vintage buggy chassis.
Used when using 2.2 inch tires.
38mm width.
<Compatible chassis> *2.2 inch tires are required for each vehicle.
No.30617 Optima
No.30618 Javelin
No.30619 Turbo Optima
No.30622 Optima Mid
No.30625 Ultima
Machined brass rear axle cap. Increases the weight distribution on the rear wheels for improved downhill performance.
Optional parts for INFERNO MP10 series and MP9 series. Light weight 47T spur gear for use with smaller diff for the center(Same as front and rear diff). By using the smaller diff, acceleration will be quicker and smoother. Smoother deceleration can also be achieved. This spur gear is design to fit the smaller diff case replacing the stock diff housing which is larger. Requires to use with IF403B Diff case set.
Carbon Rear shock tower for the MP10 / MP10 TKI2 / MP10e. Designed to use with MP10TKI2 long shocks. Light weight and durable carbon allows lower CG. The slightly more flex feel allows a different feel than the aluminum shock towers. A great setup option for various tracks.
A connector that allows the LED light unit (MZW429R) to be installed in double.
* MZW439R for ICS connector is not supported.
A pair of pre-glued tires and wheels assembled with a weight inside. Using on the front ensures excellent traction for hill climbing.
Stunning red anodized aluminum link rods for better appearance. For 110mm wheelbase.
New 1 degree hub carrier brass bushing inserts for the Inferno MP9 / 10. Increased durability and more weight to increase traction.
Can be installed on MR-03VE, MA-015, MA-020VE and MB-011.
Machined aluminum steering blocks. Available in 0.5°, 1.5°, and 2.5° camber angles, based on the standard 0°. Similar to the MZW702, they feature a realistic design that allows adjustment of the upper arm mounting position and kingpin tilt, just like full-scale vehicles. When combined with the MZW702, fine-tuned adjustments can be made from 0°to 3°in 0.5°increments.
High-precision, high-rigidity CNC machined 6061T6 aluminum servo mount.
Controls rear pitching to minimize vibration. Delivers strong direct line running as well as cornering. (Includes silicon oil)
* This product is not compatible with the MM2 motor case
CNC machined 2.5mm thick carbon front and rear suspension plate, rear side plate set. Lighter and much stronger than normal aluminum
CNC machined 3mm thick carbon shock stay. The strength is significantly improved compared to the normal FRP product.
Carbon Radio plate for the MP10. Carbon allows lighter weight without sacrificing durability.
22 degrees caster angled Aluminum front hub carrier. Compatible with MP10 / MP10 TKI2 / MP10e. Bigger angle increases stability on bumpy tracks.
Optional parts for the INFERNO MP10.
By covering the joint part of the universal swing shaft with an aluminum cap, it has the effect of preventing splashing of grease and improved durability, as well as protecting a damage from dust.
It also protects the pins from falling off in case of damaging the joint parts.
Optional parts for the INFERNO MP10.
Hard type suspension arm increases response and rigidity. Allows easy control when landing.
Optional front springs for the MP10/MP10e. Thicker and more coil turn allowing stiffer characteristics. Best for high speed and high traction surfaces.
CNC machined 3mm thick carbon shock stay. The strength is significantly improved compared to the normal FRP product
Carbon front shock tower for the MP10 / MP10 TKI2 / MP10e. Designed to use with MP10TKI2 long shocks. Light weight and durable carbon allows lower CG. The slightly more flex feel allows a different feel than the aluminum shock towers. A great setup option for various tracks
Carbon front upper plate for the MP10. Carbon allows lighter weight without sacrificing durability.
Optional parts for INFERNO MP10. Front Shock Stay for IF484 MS Shock set.
Changed the existing shock mounting hole position to upper side.
Allows a longer shock travel than standard, which improves the performance when landing of jumps and bumpy section.
New 0 degrees hub carrier brass bushing inserts for the Inferno MP9 / 10. Increased durability and more weight to increase traction.
Reciver unit for the MINI-Z EVO chassis.
Supports the KT-531 and KT432PT transmitters.
Optional parts for the INFERNO MP10/MP9e Evo.
New setting weights by 10g and 20g which can be installed the main chassis.
Can be adjusted the weights in 10g/20g/30g/40g by weights combination.
Fixing by screws and nylon nut which prevents falling off when driving.
Reduces the weight of chassis by using lightweight titanium rods.
Improves steering response and suspension movement. Includes Upper Rods for Front & Rear, Steering Tie Rods and Steering Servo Rod, 7pcs in total.