Option parts for the TURBO OPTIMA.
Soft compound of 50mm tire. For low grip road surface

Back plate for the KE21 SP / KE25SP / KE25SP2 engine. Back plate elimintes the pull start allowing the use of starter boxes. Less friction allows more performance.

Optional parts for INFERNO MP10e. Battery spacer for short LiPo batteries.
It is getting popular to use the shorty LiPo batteries to 1/8 EP Buggy due to the improved performance. The battery can be changed the installing position in the battery holder to adjust a center of gravity and balance as well as making weight reduction. That are advantage to use with the shorty LiPo battery. When use the shorty battery to MP10e, it has same effect for car. It can also be used with vintage Scorpion, Beetle and Fazer series.

Lightweight Carbon Rear Shaft for the FANTOM EP 4WD. Improves throttle response by lighter rotating parts. The screw part at tip of differential side is assembled with aluminum parts by factory. Recommended to use with EFW003.

Option Parts for LAZER ZX-6.

Tie-rod set for the MA-03F/MA-030. Provides four steps of toe angle setup for each narrow and wide configuration.

Option Parts for PLAZMA Lm-C

Spare Parts for RC Surfer 3.

<Readyset Contents>
●Fully assembled and painted chassis
●3ch transmitter

<Required for Operation>
●1 x PP3 9V alkaline battery for transmitter
●4 x AAA alkaline batteries for model

Optional parts for the INFERNO MP9/MP10.
Allows to change the inside center differential gear ratio from 10T/20T to 12T/18T.
By changing the differential effect, improve running stability on bumpy track
Increased a setting variety.

Spare parts for Javelin. Great option part for the Optima.

●FH5U: SXR(SANWA XTREME RESPONSE) MODE-COMPATIBLE
●SSL-COMPATIBLE PROGRAMMABLE SERVO
# Compatible with CODE 10 (M12S, EXZES ZZ, MT-44)
Not Compatible with CODE 5 (M12, EXZES Z, MT-4S, MT-4, MT-S)
●PGS SETTING GEAR-COMPATIBLE
●SUPER RESPONSE (SSR) MODE-COMPATIBLE
●HIGH RESPONSE (SHR) MODE-COMPATIBLE
●Li-Po 2 CELL-COMPATIBLE
●HIGH TORQUE TYPE
●BRUSH LESS MOTOR
●FULL ALUMINUM CASE
●FULL METAL GEAR (Strengthening Gears) 
●AL HEAT SINK
●Black Harness

Spare parts for Javelin. Compatible with the Optima to use the Javelin roll cage body.

5600KV brushless motor for the MINI-Z sereies.

Spare parts for the MA-030EVO Chassis

Pit mat with cool MINI-Z logos. 
Great for maintanance of your MINI-Z while keeping the pit table clean. 
Soft and grippy PVC material avoids small parts to fall off the table. 
Size: 24 in. x 17 in. (approx 600 x 430mm).

Spare parts for the Mini-Z AWD

Spare Parts for TURBO SCORPION

Spare Parts for TOMAHAWK

Spare Parts for TOMAHAWK

Spare Parts for SCORPION 2014

Spare Parts for OPTIMA

Option parts for Hang-on Racer

Spare Parts for TF7

Option Parts for OPTIMA

Light weight 2.5mm carbon fiber shock tower. Compared to the stock aluminum shock tower the carbon fiber shock tower is much lighter and with the same durability

Light weight 2.0mm carbon fiber side plates. 5g lighter without compromising the durability.

Light weight 2.5mm carbon fiber plate. Same durability as the stock plates but 5g lighter.

Optional parts for the TURBO OPTIMA. 
Color variation of 50mm wheel. 
When use with #OTT244M, it can be used as optional parts for the OPTIMA and JAVELIN.

Spare Parts for TURBO SCORPION

Turns：15.5Ｔ
Operating Voltage：1-3Ｓ／12.6Ｖ
RPM@7.4V：18870
KV（RPM／V）：2550
Max Current：38A
Max Power：320W
Efficiency：90％
Weight（g）：179
Motor Diameter（mm）：35.8
Motor Length（mm）：51.2
Shaft Length（mm）：15
Shaft Diameter（mm）：3.175

Tie rod set changes front toe angle of MR-03.

3 types of wire diameters can be chosen for both front and rear. Provides a wide range of setting options

※Old Parts #：IF122C

＜サイズ＞
■542×300×397mm

■Length 430mm
■Width 197mm
■Ground Clearance 5mm approx.
■Wheelbase 270mm
■Tread (F/R) 164mm / 166～172mm
■Wheel（F/R） Φ36mm x 30mm / Φ36mm x 45mm
■Weight 1,100g approx.
■Motor Brushless (sold separately)

Required for operation

●2-channel, 1 servo R/C system for cars
●Brushless motor
●ESC for brushless motor
●Battery
●Battery charger for chassis battery
●Tires
●1/10 Formula car body
●Tools
●Paint for body
●Batteries for R/C system

■Length　490mm
■Width　307mm
■Height　180mm
■Ground Clearance　28mm
■Wheelbase　325mm (4 settings available by changing rear hub collar position)
■Tread (F/R)　254mm (2 front settings and 3 rear settings available by changing bushes)
■Tire (F/R)　φ116 x 44mm
■Gear Ratio　11.7:1
■Weight　3,370g approx.
■Engine　KE21V (recoil starter installed/rear exhaust)

<kIT cONTENT>
●Factory assembled chassis installed with R/C system
●Printed pre-cut body complete with coloring
●Pre-installed KE21V engine with rear exhaust
●Syncro KT-331P transmitter
●1.5, 2.0, 2.5mm Hexagonal wrench
●Cross wrench (small)
●17mm Wheel wrench

<Require for operation>
●AAA x 8 alkaline batteries for transmitter
●Fuel
●Starting tools (Fuel bottle, Plug heater)

■Length 383mm (Including body)
■Width 323mm
■Height 200mm (Including body)
■Wheelbase 274mm
■Tread (F/R) 250mm
■Tires (F/R) φ110×70mm
■Gear Ratio 11.69:1
■Motor G14L
■Weight 2,350g (approx.)(When using 7.2V3600 NiMH)

<Readyset Contents>
●Factory assembled chassis with built in R/C unit
●Factory finished body with decals applied
●Syncro KT–231P+ transmitter
●Hex wrench
●Integrated spanner
●Setting change parts

<Required for Operation>
●4 x AA batteries for transmitter
●Battery for chassis (recommended: 7.2V Ni-MH battery)
●Charger for battery for chassis
●Tools

■Length 165.5mm
■Width 74.5mm
■Height 49.0mm
■Chassis MR-04N-RM
■Wheelbase 86.0mm （S）
■Tread F:59.5mm R:61.0mm
■Front Wheel Offset Narrow +1.5mm
■Rear Wheel Offset Wide +1.0mm
■Weight 168.6g
■R/C System Syncro KT-531P

<Readyset Contents>
●Factory assembled chassis
●Pre-painted body, complete with markings
●2.4GHz Perfex KT-531P 2.4GHz transmitter
●Front tread adjustment parts set
●Pinion gears 6T, 7T, 8T, 9T
●Spare nuts
●Wheel wrench
●Pinion gear tool
●Tires, wheels

<Required for Operation>
●AAA-size alkaline batteries x 4 for chassis.
●AAA-size alkaline batteries x 4 or Ni-MH batteries x 4 for transmitter

■Length 165.0mm
■Width 68.0mm
■Height 53.0mm
■Wheelbase 94.0mm（L）
■Tread  F : 58.5mm R : 58.5mm
■Chassis MA-020-N
■Front Wheel Offset Narrow ±0.0mm
■Rear Wheel Offset Narrow ±0.0mm
■Weight 167g
■R/C System Syncro KT-531P

<Ready set contents>
● R / C unit built-in complete chassis
● Painted and marked complete body
● Syncro KT-531P transmitter
● Mini pylon
● Pinion gear (15T, 17T, 19T, 21T)
● Spur gear (27T, 29T, 31T)
● Spare nut
● Wheel wrench
● Pinion removal tool

＜ Required for Operation ＞
●AAA-size alkaline batteries x 4 or Ni-MH batteries x 4 for chassis.
●AAA-size alkaline batteries x 4 for transmitter

■Length 353mm
■Width 172mm
■Height 86mm
■3P suspension system with direct drive
■Wheelbase 201-202mm（Adjustable）
■Tread F:137mm/R:133mm
■Tire F:φ48×23mm/R:φ53×35mm
■Gear ratio 3.38：1
■Weight approx 900g(with GAB4202）
■Motor 540class（sold separately）

<Kit Contents>
●Chassis kit
●Adhesive shaped tire
●Unpainted body
●Decal
●Wheel wrench（12/4.0）
●5.5/5.0wrench
●Shock wrench
●Shock oil

＜ Required for Operation ＞
●Radio transmitter with 2 channel, 1-servo
(Receiver size:L37xW27xH16.5mm / Servo size:L37xW16.5xH30mm)
●1 Electronic speed controller (ESC size：38x31x23mm)
●540 Motor
※Please use a motor with a shaft length of 15mm or more.
●Battery for chassis
●Batteries for transmitter
●Charger for Battery
●Paint for body

■Length 161.0mm
■Width 72.0mm
■Height 52.0mm
■Wheelbase 94.0mm（L）
■Tread F : 61.5mm R : 59.0mm
■Chassis MA-020-N
■Front Wheel Offset Narrow +2.5mm
■Rear Wheel Offset Wide ±0.0mm
■Weight 193g
■R/C System Syncro KT-531P

<Ready set contents>
● R / C unit built-in complete chassis
● Painted and marked complete body
● Ｓyncro KT-531P transmitter
● Mini pylon
● Pinion gear (15T, 17T, 19T, 21T)
● Spur gear (27T, 29T, 31T)
● Spare nut
● Wheel wrench
● Pinion removal too

＜ Required for Operation ＞
●AAA-size alkaline batteries x 4 or Ni-MH batteries x 4 for chassis.
●AAA-size alkaline batteries x 4 for transmitter

■Length 158.0mm
■Width 72.0mm
■Height 43.0mm
■Chassis MR-04W-MM
■Wheelbase 98.0mm （LL）
■Tread F:61.5mm R:59.0mm
■Front Wheel Offset Narrow ±0.0mm
■Rear Wheel Offset Wide ±0.0mm
■Weight 167.8g
■R/C System Syncro KT-531P

<Readyset Contents>
●Factory assembled chassis
●Pre-painted body, complete with markings
●2.4GHz Perfex KT-531P 2.4GHz transmitter
●Front tread adjustment parts set
●Pinion gears 6T, 7T, 8T, 9T
●Spare nuts
●Wheel wrench
●Pinion gear tool
●Tires, wheels

<Required for Operation>
●AAA-size alkaline batteries x 4 for chassis.
●AAA-size alkaline batteries x 4 or Ni-MH batteries x 4 for transmitter

■Length 180.0mm
■Width 78.0mm
■Height 40.0mm
■Chassis MR-04W-LM
■Wheelbase 102.0mm （3L）
■Tread F:64.5mm R:63.0mm
■Front Wheel Offset Narrow +1.5mm
■Rear Wheel Offset Wide  ±0.0mm
■Weight 182.2g
■R/C System Syncro KT-531P

<Readyset Contents>
●Factory assembled chassis
●Pre-painted body, complete with markings
●2.4GHz Perfex KT-531P 2.4GHz transmitter
●Front tread adjustment parts set
●Pinion gears 6T, 7T, 8T, 9T
●Spare nuts
●Wheel wrench
●Pinion gear tool
●Tires, wheels

<Required for Operation>
●AAA-size alkaline batteries x 4 for chassis.
●AAA-size alkaline batteries x 4 or Ni-MH batteries x 4 for transmitter

■Length 270mm
■Width 98mm
■Height 190mm
■Wheelbase 185mm
■Tire(F/R) Φ78×18mm／Φ86×23mm
■Gear Ratio 13.80：1～19.30：1
■Weight 750g  (approx.)
■Motor Le Mans DM20

<Kit Content>
●Chassis kit
●Pinion gear (10T, 12T, 14T)

<Required to run>
●2ch R/C system
●Batteries for transmitter
●servo×1 (Recommended: NoGPW20)
●ESC×1 (Recommended: No.GPW17)
●Battery for chassis（7.2V-1600mAh Ni-MH)
●Charger for battery 
●Charger Convert Connector
●Grease（Recommended:No.96508)
●Paint
●Tool

■Length  167mm
■Width  106mm
■Height  56mm
■Wheelbase 115mm
■Tread (F/R) 89mm/89mm
■Tire(F/R) F37 x 13.5mm/F37 x 18.5mm
■Weight  200g (approx.)
■Motor  130 class
■Battery AAA alkaline x 4
■R/C System KT-531P FHSS 2.4 GHz

＜Readyset Contents＞
●Factory assembled chassis with pre-installed R/C unit
●KT-531P transmitter
●Pre-painted polycarbonate body finished with markings
●Pinion gears (11T, 13T, 15T)
●Spur gears (33T, 35T)
●Pinion gear tool
●Pairing stick
●Wheel wrench
●Spare nuts for wheels

＜Required for operation＞
●AAA alkaline batteries x 4 or NiMH batteries x 4 for chassis
●AAA alkaline batteries x 4 for KT-531P transmitter

■Length (Body included) 452mm
■Width (Body width * Excluding mirrors) 192mm
■Width (chassis) 190mm
■Height 135mm
■Chassis Height 12mm (approx.)
■Wheelbase 274mm (240-274mm ※Adjustable)
■Tread（F）172mm
■Tread（R）180mm
■Gear Ratio 9.1：1
■Tread（F/R）φ63×24mm
■Weight 約1,450g
■Motor G22
■R/C system  Syncro KT-231P+

<Kit Contents>
●Completed chassis with R/C radio installed
●Factory assembled body complete with color scheme
●Syncro KT-231P+ transmitter
●1.5/2.0mm Hexagonal wrench
●Cross wrench (small)
●Setting change parts

<Required for Operation>
●4 x AA batteries for transmitter
●Battery for chassis (recommended: 7.2V Ni-MH battery)
●Charger for battery for chassis
●Tool

• • 

    Instruction Manual

※The user manual is not included with this product. You can download the user manual from the following link.

<Kit Content>
●MR-04 EVO2-W-MM Factory assembled chassis with KYOSHO SPEED HOUSE KV8500 brushless motor
●Parts set for changing front tread
●6T・7T・8T・9T Pinion gears
●Wheel wrench
●Tools for pinion gears
●Spare wheel nuts

＜Required for Operation＞
●Transmitter
●Receiver unit (Compatible with EVO/EVO2)
●ASC
●AAA x 4 batteries for chassis
●Batteries for transmitter

• • 

    Instruction Manual

※The user manual is not included with this product. You can download the user manual from the following link.

<Kit Content<
●MR-04 EVO2-W-MM Factory assembled chassis with KYOSHO SPEED HOUSE KV5600 brushless motor
●Parts set for changing front tread
●6T・7T・8T・9T Pinion gears
●Wheel wrench
●Tools for pinion gears
●Spare wheel nuts

＜Required for Operation＞
●Transmitter
●Receiver unit (Compatible with EVO/EVO2)
●ASC
●AAA x 4 batteries for chassis
●Batteries for transmitter

■Length 166.5mm
■Width 75.0mm
■Height 44.0mm
■Chassis MR-04W-MM
■Wheelbase 98.0mm （LL）
■Tread F:66.5mm R:65.0mm
■Front Wheel Offset Narrow +1.5mm
■Rear Wheel Offset Wide +1.5mm
■Weight 165.8g
■R/C System Syncro KT-531P

<Readyset Contents>
●Factory assembled chassis
●Pre-painted body, complete with markings
●2.4GHz Perfex KT-531P 2.4GHz transmitter
●Front tread adjustment parts set
●Pinion gears 6T, 7T, 8T, 9T
●Spare nuts
●Wheel wrench
●Pinion gear tool
●Tires, wheels

<Required for Operation>
●AAA-size alkaline batteries x 4 for chassis.
●AAA-size alkaline batteries x 4 or Ni-MH batteries x 4 for transmitter