There are 9452 products.
Active filters
Friction type pitching damper. Damping effect can be adjusted by viscosity of silicone oil or grease applied.
Carbon light weight rear shock towers for FZ02/02L chassis. Durable light weight shock towers allows 4 shock setting adjustments.
Carbon light weight front shock towers for FZ02/02L chassis. Durable light weight shock towers allows 4 shock setting adjustments
■Length 490mm
■Width (Body width * excluding mirror) 208mm
■Height 138mm
■Chassis Height 15mm(approx.)
■Wheelbase 274mm
■Tread (F/R) 167mm
■Tires (F/R) φ64×27.7mm
■Gear Ratio 6.54：1
■Weight 1680g (approx.)
■R/C system Syncro KT-231P+
■Motor TORX10E
<Kit Content>
●Completed chassis with R/C radio installed
●Factory assembled body complete with color scheme
●Syncro KT-231P+ transmitter
●Hexagonal wrench
●Spanner
●Setting change parts
<Required for Operation>
●4 x AA batteries for transmitter
●Battery for chassis (recommended: 7.2V Ni-MH battery)
●Charger for battery for chassis
●Tool
Spare parts for the TURBO OPTIMA.
Optional parts for the OPTIMA and JAVELIN.
Carbon bumper brace for FZ02 / 02L chassis. Supports bumper and increases chassis rigidity.
FRP main chassi and carbon front upper plate. More rigid flex allows more responsive steering.
Carbon upper deck. More rigid than the FRP version allowing less flex and roll. Great for high traction surface.
Shock gasket for 10mm oil shocks of Scorpion series. Contains 4 pieces.
Based on the 240S 4WD (15.5T), this 240 gold motor (13.5T) has been enhanced for higher rev. Best matched for the Optima series.
2.2 inch rear wheel with offset suitable for vintage buggy chassis.
Used when using 2.2 inch tires.
38mm width.
<Compatible chassis> *2.2 inch tires are required for each vehicle.
No.30617 Optima
No.30618 Javelin
No.30619 Turbo Optima
No.30622 Optima Mid
No.30625 Ultima
Machined brass rear axle cap. Increases the weight distribution on the rear wheels for improved downhill performance.
Optional parts for INFERNO MP10 series and MP9 series. Light weight 47T spur gear for use with smaller diff for the center(Same as front and rear diff). By using the smaller diff, acceleration will be quicker and smoother. Smoother deceleration can also be achieved. This spur gear is design to fit the smaller diff case replacing the stock diff housing which is larger. Requires to use with IF403B Diff case set.
Internal resistance: 0.0011Ω
Continuous maximum current: 60A
Instantaneous maximum current: 80A
Maximum KV value (2S): 13.5T 3200KV
Driving mode: Forward / brake / forward / brake / reverse
Input voltage: 7.2V-11.1V
Compatible motor type: Sensor & Sensorless
BEC output: 6V / 2A
size (mm): 37.5 x 30.8 x 18.7
Weight (g): Approximately 80
■Length 455mm
■Width（Body width） 200mm（210mm）
■Height 120mm
■Wheelbase 260mm
■Tread (F/R) F：174mm／R：174mm
■Tires (F/R) F：φ64×24.2mm／R：φ64×24.2mm
■Gear Ratio 6.54：1
■Weight 1650g(approx.)
■Syncro KT-231P+ transmitter
■Motor G14L
Carbon Rear shock tower for the MP10 / MP10 TKI2 / MP10e. Designed to use with MP10TKI2 long shocks. Light weight and durable carbon allows lower CG. The slightly more flex feel allows a different feel than the aluminum shock towers. A great setup option for various tracks.
Spare part for the Mad Van VE. It can be used on the standard Mad Van(34412T1) as an option. Durable sintered metal materila.
Sintered 76T Spur gear for the Mad Van VE. Good optional part for the Mad Van.
Handy multiuse case with a MINI-Z logo.
Comes with an internal tray with separating plates for flexible space arrangement.
It can also be used as a storage/protection box for an on-road type MINI-Z (see below for maximum dimensions).
Dimensions: approx. 201 x 108 x 52mm
Maximum MINI-Z size: approx. 187 x 95 x 48mm
Spare parts for the INFERNO MP9 TKI4 V2/MP9e Evo. V2 / can also be used for other 1/8 buggy.
Front shock stay (5.0mm thick) for the INFERNO MP9 TKI4 V2/MP9e Evo. V2 Readyset
A connector that allows the LED light unit (MZW429R) to be installed in double.
* MZW439R for ICS connector is not supported.
A pair of pre-glued tires and wheels assembled with a weight inside. Using on the front ensures excellent traction for hill climbing.
Stunning red anodized aluminum link rods for better appearance. For 110mm wheelbase.
CNC machined motor mount for Ultima. High processing accuracy and improves cooling effect by fin shape. Gunmetallic anodized finish for dress up.
CNC machined front shock stay for the Ultima. Using a hybrid material in which FRP is sandwiched with carbon, proper hardness to improve durability.
High machining accuracy and rigidity shock stay allows suitable setting of shock.
CNC machined rear shock stay for the Ultima. Using a hybrid material in which FRP is sandwiched with carbon, proper hardness to improve durability.
High machining accuracy and rigidity shock stay allows suitable setting of shock.
Optional parts for the Fazer MK2 and the FZ02. Convenient tool when installing and removing front hub ball. The ball can be installed straight by tightening the cap screw without damaging the ball, as well as easy removing. Also useful when changing from nylon ball to optional the FAW218 HD ST ball.
Optional parts for the Fazer MK2 FZ02L-B (Rage 2.0). Durable wheel hubs.
Optional parts for the Fazer MK2 and the FZ02. High precision stainless steel machined ball for front hub. Improves the durability.
Optional parts for the Fazer MK2 Touring cars. Universal Swing shafts to replace the Swing shafts. Protects faling off the shafts when crash and improves drive efficiency.
Durable die-cast center gear to beef up the drive train.
